3 pin pogo pin connector Plug-in type type
Housing: PPA, PA46, PA9T, LCP
Pogo Pin OEM
PACK:
Bulk: aluminum foil bag.
Reel: diameter Φ330mm; carrier tape width: 12, 16, 24, 32, 44mm.
=================================================================================
product testing introduction
Electrical performance |
1 |
Contact impedance |
30 mohm Max at working stroke |
Top-Link factory testing standard* |
2 |
Insulation Resistance |
500 Mohm Min |
EIA-364-21 |
3 |
Dielectric Withstanding Voltage |
No flash-over,air discharge,breakdown or leakage |
EIA-364-20 |
4 |
Temperature Rise vs Current Rating |
30 °C Max.
temperature rise at specified current |
EIA-364-70 |
Mechanical performance |
1 |
Spring force |
refer to product drawing |
EIA-364-04 |
2 |
Retention Force |
0.5Kgf(4.5N)Min. |
EIA-364-29 |
3 |
Durability |
10,000 cycles Min.
No physical damage Resistance after test 30 mohm Max. |
EIA-364-09 |
4 |
Vibration |
No physical damage,No electrical discontinuity more than 1i second. |
EIA-364-28 |
5 |
Mechanical Shock |
No physical damage,No electrical discontinuity more than 1i second. |
EIA-364-27 method A |
Environmental |
1 |
Solderability |
solder coverage area Min.95% |
EIA-364-52 |
2 |
Salt Spray Corrosion |
No physical damage. Resistance after test 100 mohm Max. |
EIA-364-26 condition B |
3 |
Resistance to Solder heat(IR/convection) |
No cracks,chips,melting,orblister |
EIA-364-56 |
4 |
Humidity |
No physical damage, Resistance after test 100 mohm Max. |
EIA-364-31,method ii,condition A |
5 |
Thermal Shock |
No physical damage, Resistance after test 100 mohm Max. |
EIA-364-32,method ii |
6 |
Temperature Life |
No physical damage, Resistance after test 100 mohm Max. |
EIA-364-17,condition A,condition 4 |
Environmental |
1 |
peel force |
10-130 gf |
EIA-481 |
2 |
Drop Test |
|
Refer to drop test Standard of Molex |
- Remark: Considering the difference between test spot and actual work spot, the impedance test condition defined by Top-Link is based on the whole working stroke. This is what we generally said dynamic impedance testing, it differs from the static test condition of ELA-364923, the durability test standard is also based on this test condition.
- -----------------------------------------------------------------------------------------------------------------------------------------------------------
- KLS is equipped with comprehensive inspection and reliability testing equipment.
- KLS attaches great importance to quality management of each link, including IQC, IPQC, 100% dynamic testing of spring force and contact impedance , 100% appearance inspection, FQC sampling inspection, CQC, design verification, regular reliability testing, failure analysis, and so on.
- KLS has implemented strict and effective quality control over each link which includes product design, sample preparation, trial production and mass production. As a consequence, our product quality is guaranteed.
- ==========================================================================================
- pogo pin connector OEM type
1, small diameter, fine type products
The minimum can be done is below 0.75
2, high durability
Maximum durability of up to 1 million times
3, large current
Maximum up to 15A current
4, high reliability
100% dynamic impedance testing to ensure 100% functional zero defects
5, lower operating height
Minimum working height of up to 1.5mm, the chopping block can be lower
6, high precision (size & forward force)
Height tolerances up to +, - 0.05mm positive up to + / - 10%
7, non-standard structure
Customer requirements can be customized according to customer requirements, such as: mushroom head structure
|